The Cutest Wood Bead Easter Wreath: A Tutorial

[Disclaimer: Finding Mandee is reader-supported, if you purchase through links on my site I may earn an affiliate commission at no additional cost to you. As an Amazon Associate, I earn from qualifying purchases.]

If you’ve been around this blog, then you know that I have wreaths for every holiday!

I have multiple to choose from for every season:

winter (Christmas and Valentine’s Day)

Last year, during quarantine, I made a wood bead wreath and it turned out so good, that I had to have another one, but in the shape of a bunny.

Here’s how I made this adorable wood bead Easter wreath!

DIY Wood Bead Easter Wreath Tutorial | Finding Mandee

Step 1: Gather the Easter Wreath Supplies

For this wreath, you will need:

12″ embroidery hoop
18″ wood bead wreath with 1″ beads (or pack of 1″ wood beads)

pen or pencil (not pictured)

Supplies for the DIY wood bead Easter wreath. — *(Supplies for the wood bead Easter wreath.)*

Step 2: Make the Ears

The first step to making your Easter wreath is to make the bunny’s ears.

Use your wire cutters to cut the 18″ wreath in half and remove the beads. Then bend the metal frame of the wreath halves into bunny ears.

Pro Tip: To make perfect bunny ear shapes, place one bead at the center of the half circle and bend the wire in half until the 2 ends meet.

Making the bunny ears for the wood bead wreath. — *(The bunny ears were easier to shape than I thought.)*

After shaping the ears, lay them against the embroidery hoop to decide the placement.

Bend the base of the ears out a little wider to give them more stability. Then mark the placement of the ears on the embroidery hoop with your pencil.

Decide the placement of the ears on your Easter wreath. — *(It was already looking cute, even with its bare bones.)*

Hobby Lobby Wood Bead Wreath – 18 Mr. Pen- Wire Cutter, 6 Inch, Wire Cutters, Diagonal Wire Cutters, Flush Cutter, Nippers, Side Cutters, Flush Cutters, Diagonal Cutter, Cutting Pliers, Floral Wire Cutter, Wire Pliers

Step 3: Glue Down the Split Beads

While I already had the wreath lying flat, I glued down the split wood beads. Using hot glue, I attached the split beads to the edge of the embroidery hoop.

I left a large gap between the beads at the top of the wreath, but this will be filled with flowers later.

Glue the split wood beads to the edge of the embroidery hoop. — *(The bunny’s head is done!)*

Unfinished Split Wood Balls 20 Pcs 2 Inch Diameters Half Wooden Balls Mini Hemisphere Half Craft Balls for DIY Projects Kids Arts and Craft Supplies Caydo 12 Inch Embroidery Hoop Bamboo Circle Cross Stitch Hoop Ring for Art Craft Handy Sewing

Step 4: Attach the Ears

Attaching the ears to the embroidery hoop was the most frustrating and difficult part of the whole project.

In one video I found, the lady wrapped the wire she used around the base of her wreath. However, the wire that I was using from the wood bead wreath was much too thick and stiff to wrap around the embroidery hoop.

Attaching the ears to the bunny wreath was the hardest part. — *(Yay for husbands with power tools!)*

After watching me struggle, my husband decided to drill holes in the embroidery hoop using a tiny drill bit. The drill bit is roughly the same size as the wire used to make the ears.

If you don’t have a power tools, there are hand drills that are used in jewelry making that would also work for this!

Once the holes were drilled, we pushed the ear wires through, bent the wire as close to the embroidery hoop as possible, and added hot glue to hold them in place.

Bend the wire and add hot glue to secure the bunny ears to the embroidery hoop. — *(We added hot glue to the wire that was cut too short to keep it secure.)*

CRAFT911 Hand Drill Bits Set – Pin Vise Hand Drill Manual, Small Micro Drill Bit Set | Jewelry Drill Kit, PCB Mini Drill Bits for Resin Beads Polymer Clay | DYI Jewelry Making Drill, Craft Drill Bit Liumai Hot Glue Gun Kit with 30pcs Glue Sticks, Mini Hot Melt Glue Gun with Carrying Case for Crafts, School DIY Arts, and Home Repair (30Watts, Pink)

Step 5: Add the Flower Crown

Finally, it was time to add the bunny’s flower crown!

Cut or pull the flowers from their stems and separate the small stems of greenery from the bush.

I used 2 large peonies in different shades of pink, small white flowers, and a bush of eucalyptus greenery.

Place your greenery first, then the white flowers, and follow with the peonies. Secure all of them to the exposed section of the embroidery hoop using hot glue.